wediscount2

Hansel, not sure who made them but they are old vintage marbles. Ronnie

Looking for a few smaller marbles to restore. Will accept better grade marbles in exchange for my labor. Ronnie

Would like to no who made it. Ronnie

If it doesn't sell I would be interested in some of the vintage marbles. Ronnie

Keep each of your pictures between 800KB and 1Megabyte and your pictures should be just fine. Ronnie

Haven't seen you in a while. Hang in there Scott. Just get better. Ronnie

Steph, need to see a picture of your friend's marble as it could be a 10 dollar marble or a 1000 marble. Ronnie

Each grit reduces the size of the "crater" left by the previous grit by a great percentage. The 60-90 grit leaves thousands of small craters. The 200 grit removes these craters but in turn creates it's own craters. The 600 grit will remove the 200 grit craters, and leave the very outer glass surface ready to accomadate a nice high lustre final polish. The 600 grit will also leave micro craters but the cerium oxide working in conjunction with friction will ultimately diminish the craters requiring a strong loupe to detect them. Ronnie

Bought this tumbler at a flea market. It was new, never used. I like it a lot. It is very quiet and it never leaked a drop of slury while I used it. It will do about 100 marbles each grind & polish. It's best to reduce the size of big chips with the dremmel tool. If you don't marbles tumbling will get into the chip and start dishing it out creating a valley. In other words it will turn a chip into a big smooth valley. Not really necessary to dremmel small chips. The tumbler will do that for you. I had 6 marbles that had at least one good size chip on it. I took a grinding stone and using a dremmel tool, I went around the perimeter of the chip starting appr. a quarter inch away from the edge of the chip and raising the tool up to the marbles chip edge. Do this all the way around the marble. Don't worry about the flat grooves the dremmel leaves as the tumbler will straighten all that out. Also don't worry about the wheel busting the marble as it will not do so. After grinding let the marble naturally cool down to ambient temp., usually a minute or two. Also wear a mask or do it outside and let the wind carry the glass dust away from you. DO NOT BREATHE THE DUST!! To begin the tumbling put your marbles in the tumbler and add enough water to fill the drum about "HALF FULL". Then put in 2 decent tablespoons of 60-90 grit. Although quiet I turned my machine off at night. I let it run 3 days or about 30 hours. I checked my work once during the 3 day rough grind. (after 10 hours). Every thing looked real good so I finished out the 30 hours. I felt it was time for the next step, the 200 grit. I washed the drum and marbles real good after the 60-90 run. Put the marbles back in the drum, put in water to bring it up to half way full, then I put 2 decent tablespoons of 200 silicon carbide grit. Again I let this run for at least 30 hours. Now this is important. The 200 step is the most critical of all steps. If you do the 200 proper I can assure you the marbles will polish out with a decent lustre. (2 more steps to go after the 200). Tired of typing, taking a break, will post later the final 2 steps, the 600 grind and the cerium oxide polish. Also on my polish I forgot to put in a teaspoon of dish soap. A couple of people that do this frequently told me the soap makes for a high gloss polish. (suppose to add the soap 8 hours before they are done). Ronnie

Galen, It is a rotary and I am going to post here this morning on how I used it as I feel it would be helpful if someone was going to attempt it. Ronnie

Members, Thought I would send some photos of a group of marbles I ground and polished using a rock tumbler. I finished them up about a week ago. I had tried many years ago to tumble some mib's, but I had terrible results. The marbles I used all had some degree of damage, even the Jabo's. It took some doing but I finally got them to look fairly good. What truly amazed me was how good and round they "all" turned out. One friendly word of advice. If you try a rock tumbler, between grit's examine and make sure the grit is finished doing it's intended job before moving on to the next grit size. Have patience, it takes a long time to do a good job. I have a friend who has 4 marbles with the grit used to make it look that way. The grit used is marked on each marble. I will get him to send me a photo of them setting side by side and I'll post it here for edification purposes. Ronnie

The first one has been heavily polished. The second one looks pretty much original. Ronnie

An epoxy coating fill's the bill. Ronnie

Those 2 marbles are such killers they ought to be outlawed. Ronnie

Two nice looking marbles. Ronnie

Hansel, Those thing's are a work of art. Ronnie

Glass Sulphide of Beetle Bailey.

Would like to see and hold them. They may have some age to them. Ronnie

eBay prostitutes this wrong doing by not allowing the public to contact the winning bidder to let them know they just got ripped a new one. Shamie, shamie on the bay. Ronnie

Hansel, forgot to add, the numbers would have been used by the sales man to place the order into the Akro Agate Co. from the prospective buyer. EI: Give me a half dozen of # 54, a dozen #40 etc, etc, and send them to Henry's general store blah, blah, blah, Ronnie

Hansel, Looks like a sales rep box probably made up at Akro for their sales staff. All the marbles look original, and it's anyone's guess as to the missing one's. Ronnie

Rich, Like the Christensen neon orange. Nice MIB, Ronnie

Robert, would be really helpful if you brought up the subject matter again and elaborated a little bit on it on how and why you shoot your pictures in a low res and then their was one particular step you took to make them look good. Your close up's are really nice. Ronnie

I have a friend who has some with that pattern but a different color and I think Steph is correct in her Asian assessment. Ronnie

Thanks for taking your precious time to enlighten collectors to this great service. Ronnie